ChatterBank1 min ago
Burglar Alarms.
10 Answers
We live in the country and have a burglar alarm. This goes off regularly and we've had the system checked a few times. The engineer says it's spiders that set off the alarm as there's nothing wrong with it and we do find very big spiders in the house!! Somebody told us to put conkers by the alarm. Are there any more positive suggestions anyone can come up with as our neighbours are getting fed up!!! Thank you for any advice however small.
Answers
1 to 10 of 10
Best Answer
No best answer has yet been selected by Bramleyboy. Once a best answer has been selected, it will be shown here.
For more on marking an answer as the "Best Answer", please visit our FAQ.
Is it always the same zone/PIR going off ??
We had the same problem a while ago at our previous house.
The alarm had always been fine, then it started playing up, going off nearly every day and it was always the same PIR.
Well, I decided to open up the PIR and what did I find inside ?? .... a small spider that had prob got in through the little hole where the cable went into the unit itself. Obviously every time the spider cross the sensor, it was picked up and the alarm went off. Solution - spider evicted and some silicone sealant applied round the hole with the cable, to stop other spiders gaining entry.
My advice - check the inside of your PIR's .... you just never know what's lurking inside :P
We had the same problem a while ago at our previous house.
The alarm had always been fine, then it started playing up, going off nearly every day and it was always the same PIR.
Well, I decided to open up the PIR and what did I find inside ?? .... a small spider that had prob got in through the little hole where the cable went into the unit itself. Obviously every time the spider cross the sensor, it was picked up and the alarm went off. Solution - spider evicted and some silicone sealant applied round the hole with the cable, to stop other spiders gaining entry.
My advice - check the inside of your PIR's .... you just never know what's lurking inside :P
I'm with Old_Geezer on this one: you need to find a better security firm!
Consider how a spider might be setting off your alarm system. For example, it would have to be a ruddy big spider to activate a pressure pad! Similarly, I've never heard of a spider managing to open a window (and thus break the circuit between the window and its frame). At a guess, I'd assume that spiders are breaking the beam (by crawing across the sensor) on an infra-red system. So the solution is simply to get a system that doesn't use infra-red beams (e.g. a system that identifies an 'open circuit' when a door or window is opened and/or has pressure pads in place inside doors and windows).
Consider how a spider might be setting off your alarm system. For example, it would have to be a ruddy big spider to activate a pressure pad! Similarly, I've never heard of a spider managing to open a window (and thus break the circuit between the window and its frame). At a guess, I'd assume that spiders are breaking the beam (by crawing across the sensor) on an infra-red system. So the solution is simply to get a system that doesn't use infra-red beams (e.g. a system that identifies an 'open circuit' when a door or window is opened and/or has pressure pads in place inside doors and windows).
Of all the comments above, I find Gizmonsters the most plausible.
The IR sensors that I use have a link jumper inside that can be adjusted for one, two or three `hits` in short succession before the signal is returned to the control box. The normally used setting is one, but I have had to change one sensor to setting two before it would cease false triggering every now and again.
I think most of these little boxes are made to one industry standard, as an OEM item. Worth a look inside.
It isn't about plods coming out, SD, its about the blighters being dissuaded to continue once the alarm triggers. Generally works unless you are located miles out in the sticks with no neighbours.
The IR sensors that I use have a link jumper inside that can be adjusted for one, two or three `hits` in short succession before the signal is returned to the control box. The normally used setting is one, but I have had to change one sensor to setting two before it would cease false triggering every now and again.
I think most of these little boxes are made to one industry standard, as an OEM item. Worth a look inside.
It isn't about plods coming out, SD, its about the blighters being dissuaded to continue once the alarm triggers. Generally works unless you are located miles out in the sticks with no neighbours.
It could be a spider, this is not unknown with intruder alarms. However, another area to look at is the PIRs. Inside these units there are normally a set of small posts that have a link between some of them. By adjusting the link (moving it to connect different posts together) the pulse count of the PIR can be altered thereby making it less (or more) sensitive. This of course varies from model to model but may cut down or eradicate your false alarms.
l'm assuming you are closing doors and windows, and not leaving pets in rooms covered by sensors.
Good luck, I know it's annoying when it happens.
l'm assuming you are closing doors and windows, and not leaving pets in rooms covered by sensors.
Good luck, I know it's annoying when it happens.
1 to 10 of 10
