Jobs & Education1 min ago
heated towel rail/ radiator
5 Answers
Our heated towel rail/radiator in the bathroom is letting out very little heat. We have tried bleeding it with no improvement. Any ideas as to what the problem might be would be appreciated, Thankyou.
Answers
Best Answer
No best answer has yet been selected by Mrspoppins. Once a best answer has been selected, it will be shown here.
For more on marking an answer as the "Best Answer", please visit our FAQ.We had a similar problem for many years in our en-suite bathroom where the radiator never became more than tepidly warm. When our boiler was replaced two years ago we mentioned this to the installers, They checked the pipework and found that there had been an almost permanent blockage ever since the house was built. The pipework was replaced and our radiator is now always piping hot. Perhaps a good Corgi gas fitter could diagnose the problem for you.
It probably needs balancing in relation to the other rads on the system.
In short, the volume flow of water going through it is not as great as the volume going though the other rads.
Take off the plastic top of the lockshield valve (the one at the OTHER end from the one with splines on it that you can adjust [or at the other end from the thermostatic valve - if you have one fitted]).
Turn the splined shaft NO MORE than one quarter turn anticlockwise and monitor what happens over the next hour or so.
If it is noticeably hotter, you are getting somewhere.
Adjust further in quarter turn stages if necessary.
In short, the volume flow of water going through it is not as great as the volume going though the other rads.
Take off the plastic top of the lockshield valve (the one at the OTHER end from the one with splines on it that you can adjust [or at the other end from the thermostatic valve - if you have one fitted]).
Turn the splined shaft NO MORE than one quarter turn anticlockwise and monitor what happens over the next hour or so.
If it is noticeably hotter, you are getting somewhere.
Adjust further in quarter turn stages if necessary.
Just to clarify, normally both ends of a radiator have right-angled valves that connect rad to the house pipework. One has a splined plastic cover over it and is used to turn the rad on/off. The other end often has a smooth plastic cover over and isn't intended to be moved once set up. Prise the cover off and underneath is a brass shaft (it is actually the same as the other side but with a different plastic cover). This valve is used to set-up the flow of water around the system - called balancing. If a CH system is not balanced, the water merely rushes to the rad that is closest to the pump/boiler, goes round it and back again to the boiler to be reheated. The rads that are furthest from the pump/boiler don't get a look in, and remain cool.
By balancing, the rads closest to the pump/boiler have the valve that I am referring to permanently restricted by turning the brass shaft down (clockwise) - this restricts the flow through this rad and forces more of the hot water to the rads further distances away. It takes a time to balance and normally, once set up, a householder has no reason to go poking about trying to rebalance.
All I am suggesting is that if the lockshield valve I am referring to has been turned down (clockwise) too far, this towel rail rad is not getting its fair share of circulating water.
The technique I described in the first email is how to adjust.
If you are saying the lockshield has been fully opened so that both valves are completely open and you still aren't getting any hot water through, then something is likely to be in the pipe blocking it - sludge perhaps.
By balancing, the rads closest to the pump/boiler have the valve that I am referring to permanently restricted by turning the brass shaft down (clockwise) - this restricts the flow through this rad and forces more of the hot water to the rads further distances away. It takes a time to balance and normally, once set up, a householder has no reason to go poking about trying to rebalance.
All I am suggesting is that if the lockshield valve I am referring to has been turned down (clockwise) too far, this towel rail rad is not getting its fair share of circulating water.
The technique I described in the first email is how to adjust.
If you are saying the lockshield has been fully opened so that both valves are completely open and you still aren't getting any hot water through, then something is likely to be in the pipe blocking it - sludge perhaps.