Quizzes & Puzzles1 min ago
Answers
1 to 2 of 2
Best Answer
No best answer has yet been selected by penanglad. Once a best answer has been selected, it will be shown here.
For more on marking an answer as the "Best Answer", please visit our FAQ.
(2-part post):
Place the barrel on the stillage, ensuring that it tilts slightly forward and that it can't rock about.
Whack a spile peg into the top of it. (I prefer soft spiles but, to be honest, I've never really noticed much difference if I've used hard spiles). In doing so, it helps to develop a technique so that the gas comes out of the barrel but the beer still stays in it! (Knocking a spile into a lively barrel, on a humid day in the middle of summer can easily result in an unexpected beer shampoo).
Some people like to tap the barrel at the same time. Others prefer to wait until the same day as the beer is to be drunk. If doing the latter, remember to remove the spile first, to vent the barrel. (Otherwise the pressure build up inside the barrel might result in the tap being pushed out. It's tricky enough to get it in, without losing any beer, anyway. There's no point in making the job harder!).
Leave for an appropriate time between putting the barrel on the stillage and drawing any beer off. Only experience will teach you how long 'an appropriate time' is. Most beers are fit to drink after two or three days. The longest I've known a beer take to settle and clear was 8 days. (If a beer is taking an exceptionally long time to clear,contact the brewery and seek their advice about the possibility of adding finings). Conversely, the record time for taking a barrel off the dray and drawing a perfect pint was under 2 hours!
Place the barrel on the stillage, ensuring that it tilts slightly forward and that it can't rock about.
Whack a spile peg into the top of it. (I prefer soft spiles but, to be honest, I've never really noticed much difference if I've used hard spiles). In doing so, it helps to develop a technique so that the gas comes out of the barrel but the beer still stays in it! (Knocking a spile into a lively barrel, on a humid day in the middle of summer can easily result in an unexpected beer shampoo).
Some people like to tap the barrel at the same time. Others prefer to wait until the same day as the beer is to be drunk. If doing the latter, remember to remove the spile first, to vent the barrel. (Otherwise the pressure build up inside the barrel might result in the tap being pushed out. It's tricky enough to get it in, without losing any beer, anyway. There's no point in making the job harder!).
Leave for an appropriate time between putting the barrel on the stillage and drawing any beer off. Only experience will teach you how long 'an appropriate time' is. Most beers are fit to drink after two or three days. The longest I've known a beer take to settle and clear was 8 days. (If a beer is taking an exceptionally long time to clear,contact the brewery and seek their advice about the possibility of adding finings). Conversely, the record time for taking a barrel off the dray and drawing a perfect pint was under 2 hours!
When you think that the beer might be fit to drink, remove the spile peg and take some straight from the barrel. (If you've waited until now to tap the barrel, give it half an hour or so between tapping it and trying the beer, in case the beer was disturbed when it was tapped).
If the beer is cloudy, give it another day before trying it. (If it was only slightly cloudy, it might clear later the same day). When it looks clear, taste it to check. If it tastes fine, try some more. (That's got nothing to do with the quality of the beer. It's just a cellarman's perk!).
Then attach it to a line. (I always keep lines which are out of use full of water, rather than air, to prevent oxidation of any beer residues. It also makes it easier to pull the beer through).
Pull the line through until the contents look like beer rather than water. When you're sure it's pure beer, taste it. (Again, that shouldn't be necessary but you've got to have some perks!).
When the pump is out of use (e.g. overnight) replace the spile peg to reduce oxidation of the beer.
Enjoy your beer!
Chris
If the beer is cloudy, give it another day before trying it. (If it was only slightly cloudy, it might clear later the same day). When it looks clear, taste it to check. If it tastes fine, try some more. (That's got nothing to do with the quality of the beer. It's just a cellarman's perk!).
Then attach it to a line. (I always keep lines which are out of use full of water, rather than air, to prevent oxidation of any beer residues. It also makes it easier to pull the beer through).
Pull the line through until the contents look like beer rather than water. When you're sure it's pure beer, taste it. (Again, that shouldn't be necessary but you've got to have some perks!).
When the pump is out of use (e.g. overnight) replace the spile peg to reduce oxidation of the beer.
Enjoy your beer!
Chris
1 to 2 of 2
Latest Posts
Quizzes & Puzzles22 mins ago
ChatterBank30 mins ago
Quizzes & Puzzles71 mins ago
Christmas In The Good Old Days
ChatterBank77 mins ago
Elementary Particle In First Half Of...
Crosswords135 mins ago
