Quizzes & Puzzles2 mins ago
Greenhouse - taking down and putting up
Is it easy to dismantle a greenhouse and then put it up again? I have been offered one, but don't want to take it if it is going to be too difficult. I would appreciate some advice please. Many thanks.
Answers
1 to 5 of 5
Best Answer
No best answer has yet been selected by Celtigra3. Once a best answer has been selected, it will be shown here.
For more on marking an answer as the "Best Answer", please visit our FAQ.
If you are interested in DIY and (later) in gardening, and are any way half-handy, you should have a go. I have assembled a 12by 8 aluminium house working on my own and later added an extension. I enjoyed it .Over the years I have replaced sufficient of the panes to make me believe that it would be easy to take a house down. I regret now not taking an underground electricity and water supply to the site before I constructed the base.
Take the offer. Best of luck!
Take the offer. Best of luck!
Its definately something for the DIY'er. Firstly, remember - you wont have construction directions, so a bit of patience and planning is a must. It's so easy to get carried away with the dismantling and be left with a heap of bits and a lot of head scratching!
I'd suggest you take a few photos, close-ups of joints etc. Measure the existing dimensions while the GH is still up, to help you make a base/plinth accurately. An obvious starting point is to unclip and remove the glass, may be an idea to mark the glass with felt tip pen. Horticultural glass is usually 3mm and can become brittle, so take care and dont choose a very cold day! If you have access to a trailer, van or truck, then you will save oodles of time as you will be able to remove the roof bearers, release the ends and sides and transport then in one piece. Otherwise its complete dismantle and marking up of the bits. You will almost certainly break some glass and will also need some more glazing clips, so check a local glass/hardwear supplier. Good luck - I had a 12 x 10 offered me last week where we have just completed a job - I've just persuaded myself to go for it!!
I'd suggest you take a few photos, close-ups of joints etc. Measure the existing dimensions while the GH is still up, to help you make a base/plinth accurately. An obvious starting point is to unclip and remove the glass, may be an idea to mark the glass with felt tip pen. Horticultural glass is usually 3mm and can become brittle, so take care and dont choose a very cold day! If you have access to a trailer, van or truck, then you will save oodles of time as you will be able to remove the roof bearers, release the ends and sides and transport then in one piece. Otherwise its complete dismantle and marking up of the bits. You will almost certainly break some glass and will also need some more glazing clips, so check a local glass/hardwear supplier. Good luck - I had a 12 x 10 offered me last week where we have just completed a job - I've just persuaded myself to go for it!!
My wife and I did one some years ago, I think it was about 12x6 - As I recall It took us most of the weekend.
I think we managed to get away with a couple of broken panes which we then replaced.
Mind you we got their and our friend had taken it down already and done some sketches.
It's probably quicker in the long run if they don't do this - it's easier to work from your own notes!
Is that too difficult? I guess it depends on you
I think we managed to get away with a couple of broken panes which we then replaced.
Mind you we got their and our friend had taken it down already and done some sketches.
It's probably quicker in the long run if they don't do this - it's easier to work from your own notes!
Is that too difficult? I guess it depends on you
1 to 5 of 5
Latest Posts
Quizzes & Puzzles3 mins ago
Quizzes & Puzzles8 mins ago
Crosswords16 mins ago
Crosswords22 mins ago
Related Questions
Sorry, we can't find any related questions. Try using the search bar at the top of the page to search for some keywords, or choose a topic and submit your own question.